Flight controllers
INAV vs Betaflight: Differences, Supported Boards and Which to Choose
Betaflight and INAV run on the same kind of flight controller and share an ancestor, but they are built for different flying. Betaflight is for flying the quad yourself; INAV is for GPS navigation and fixed wings. Here is how they differ, how to check which one your board supports, and what to look for in a board for INAV.
Published 21 November 2026 · by the Fioparts team, Gurugram
INAV vs Betaflight: the short answer
Betaflight is built for flying the drone yourself: freestyle, racing and cinewhoops, with the most refined flight feel and a target for almost every FPV board. INAV is built for the drone flying itself: return-to-home, position hold and waypoint missions, on multirotors and on fixed wings. Both are free, open source and run on the same class of small flight controllers, so the choice is about what you want the aircraft to do — and then about whether your board has a target for that firmware.
| Betaflight | INAV | |
|---|---|---|
| Built for | Manual FPV flight: freestyle, racing, cinewhoops | GPS navigation: long-range quads, planes, wings |
| Getting home | GPS Rescue — flies back towards home when the radio link fails, or on a switch | Return-to-home to the arming point or a saved Safehome, as a mode or a failsafe |
| Position and altitude hold | Yes, from Betaflight 2025.12 | Yes |
| Waypoint missions | An Autopilot mode with CLI waypoints arrived in 2026.6 — new | Up to 120 waypoints per mission, up to 9 missions stored on the board |
| Fixed wing | No tested support; the Betaflight docs’ own fixed-wing page says so | Fully supported, with auto launch, autotune and automatic landing |
| Other vehicles | Multirotors | Planes, gliders, multirotors, rovers and boats |
| Barometer | Optional; improves altitude estimates | Needed for altitude hold on a multirotor |
| Compass | Optional | On by default for multirotors; optional on a fixed wing |
What Betaflight does best
Betaflight’s whole development effort goes into how a quad feels on the sticks: gyro filtering, RPM filtering, feedforward and a tuning workflow built around blackbox logs. That is why nearly every freestyle and racing quad, and every tiny whoop, ships with it. It is also the firmware with the largest community, so most build videos, tuning guides and preset libraries assume it.
Its GPS features exist to save the aircraft, not to fly it for you. GPS Rescue brings the quad back towards its launch point after a failsafe so you can regain control. Betaflight 2025.12 added Altitude Hold and Position Hold modes, and 2026.6 introduced an Autopilot mode with waypoints entered in the CLI. Those are recent additions; if a planned mission is the reason you are building, INAV’s navigation has had years more flight time. Betaflight flight controllers.
What INAV does best
INAV grew out of the same Cleanflight codebase as Betaflight and went the other way: navigation first. A properly set up INAV aircraft will hold its position in wind, cruise on a heading, fly a mission planned on a map and come home on its own when the link drops.
- Return-to-home (RTH) — to the arming point or to a Safehome you have saved near your flying field, on a switch or automatically on failsafe.
- Position hold and altitude hold — the quad parks itself in 3D; on a fixed wing it loiters in a circle.
- Waypoint missions — up to 120 waypoints, planned in INAV Configurator or a ground-station app, with up to 9 missions stored on the flight controller.
- Fixed-wing tools — auto launch for hand throws, autotune and automatic landing. This is why INAV is the usual firmware for FPV wings and long-range planes.
The trade is flight feel and setup time. INAV flies a 5″ quad in acro perfectly well, but it is not tuned for racing, and a navigation build needs its GPS, compass and failsafe behaviour checked on the bench before the first flight. INAV flight controllers.
Sensors each firmware needs
- GPS — required for every navigation feature on both. Betaflight’s GPS Rescue needs a module that speaks the u-blox protocol; current M10 modules do. M10 GPS modules · all GPS modules.
- Barometer — optional in Betaflight, where it improves altitude estimates during a rescue. INAV needs one for altitude hold on a multirotor, so pick a board with a barometer on it.
- Compass (magnetometer) — optional in Betaflight. INAV uses one by default on multirotors; it can be switched off at some cost in precision. A fixed wing gets its heading from GPS once it is moving, so the compass is optional there. A GPS module with a compass built in covers both cases.
Supported boards: how to check yours
A flight controller runs a firmware only if that firmware has a target for it — a definition of which pin does what on that exact board. Betaflight and INAV keep separate target lists, and a board in one list is not automatically in the other.
- Betaflight — board definitions live in the project’s public config repository, one folder per board name. In Betaflight Configurator, the Firmware Flasher tab lists the same names; if your board appears there, it is supported.
- INAV — every release publishes one firmware file per target, named like
inav_9.1.0_MATEKH743.hex. INAV Configurator’s Firmware Flasher shows the same list, and the INAV wiki keeps a page of boards and targets. - Find the target name of a board you own — connect it, open the CLI tab and type
version. The reply names the target the board is running. Search for that name, not the name printed on the box: retail names and target names often differ.
INAV is the stricter of the two about processors. Its current releases support F405, F722, F745, F765, H743 and AT32F435 boards. The F722 has only 512 KB of flash, so INAV builds for it carry a reduced feature set. General support for F411 boards ended with INAV 7.1.2 — which rules out most whoop all-in-one boards for a current INAV build.
Choosing a flight controller for INAV
The boards that make good INAV builds share a short list of traits:
- An H743 or F405 processor. H743 has the flash and speed for every feature and is the safe choice for a board you want to keep; F405 is the value pick. Choose F722 only if you have checked that the features you need are in its build. H743 flight controllers · F405 flight controllers.
- A barometer on the board, for altitude hold.
- Enough UARTs. Receiver, GPS and a digital video system take three before you add telemetry or an airspeed sensor.
- For a plane: a wing-style board. These add servo outputs, a BEC for the servos and a built-in current sensor, so you are not wiring a separate BEC and power module.
- For a quad: the same 30.5×30.5 or 20×20 boards you would use for Betaflight, as long as an INAV target exists for the exact model and revision.
Boards in our INAV range include the Matek H743-Slim and H743-Wing, SpeedyBee F405 Wing, Holybro Kakute H7 and H743-Wing, and TBS Lucid H7. The listing for each board states the firmware it supports; confirm the revision (V3, V4 and so on) against the target list before you flash.
Video and OSD
Both firmwares draw an on-screen display for analog video through the board’s OSD chip, and both send OSD data to digital systems — DJI, Walksnail Avatar and HDZero — over a spare UART. INAV’s OSD carries more navigation elements, such as the active waypoint and a map view of home.
Can you switch between them?
Yes, when the board has a target in both. Flashing the other firmware erases the configuration, and settings do not transfer: ports, receiver, mixer, modes and tuning all have to be set up again. Before you flash, save the output of diff all from the CLI so you can return to where you were. After any switch, check motor order and direction with the props off before you fly.
Which one should you choose?
- Freestyle, racing, cinewhoop or tiny whoop — Betaflight.
- A 5″ or 7″ quad where you only want it to come back on failsafe — Betaflight with a GPS and GPS Rescue is enough.
- A long-range 7″ or 10″ that should hold position, cruise and fly home by itself — INAV.
- Any fixed wing — INAV.
- Mapping, spraying, payload work or a companion computer — neither; that is ArduPilot territory. The flight controller guide covers ArduPilot, PX4 and the processor and mounting choices.
Not sure whether a board you are looking at has the target you need? Tell us the board and the firmware and we will check before you order.
Sources & manuals
- Betaflight: GPS Rescue betaflight.com
- Betaflight: Altitude Hold and Position Hold betaflight.com
- Betaflight: board target definitions github.com
- Betaflight releases github.com
- INAV wiki github.com
- INAV: navigation modes github.com
- INAV: boards github.com